UAP 158 - The Challenge Mac OS
| Base Mount |
| Wall/Pole Mount |
Linux, Mac OS X, or Microsoft Windows 7/8/10.10 to 70° C (14 to 158° F) Operating Humidity. 5 - 95% Noncondensing. 1 Only the single-pack of the UAP-AC-EDU. UniFi Cloud Key or Dream Machine, or machine running Linux, Mac OS X, or Windows 7/8/10.
| Power Cord |
| Screws (Qty. 2) |
* Included only in the single-pack of the UAP-FlexHD
Installation Requirements
- Phillips screwdriver
- Cat5/6 UTP cable for indoor installations
- Shielded Category 5 (or above) cabling should be used for all outdoor wired Ethernet connections and should be grounded through the AC ground of the PoE.
System Requirements
- UniFi Cloud Key or Dream Machine, or machine running Linux, Mac OS X, or Windows 7/8/10
- Java Runtime Environment 1.8 or above recommended
- Web Browser: Google Chrome (Other browsers may have limited functionality.)
- UniFi Controller software v5.11.31 or newer (available at: ui.com/download/unifi)
LED | |
|---|---|
White | Factory default, waiting to be integrated. |
Flashing White | Initializing. |
Alternating White/Blue | Device is busy; do not touch or unplug it. This usually indicates that a process such as a firmware upgrade is taking place. |
Blue | Indicates the device has been successfully integrated into a network and is working properly. |
Quickly Flashing Blue | This is used to locate an AP. When you click Locate in the UniFi Controller software, the AP will flash. It will also display the location of the AP on the map. |
Steady Blue with Occasional Flashing | Indicates the device is in an isolated state (all WLANs are brought down until an uplink is found). |
Ethernet Port | |
This Gigabit Ethernet port is used to connect 802.3af PoE power and should be connected to the LAN and DHCP server. | |
Reset Button | |
The Reset button serves two functions for the UniFi AP:
| |
Determine the installation location of the UAP FlexHD:
- Desktop The UAP FlexHD stands freely on a horizontal surface such as a desktop or table/shelf. Good for temporary installations.
- Wall The UAP FlexHD is attached to a wall in a secure location.
- Ceiling The UAP FlexHD is mounted in a ceiling tile (requires optional recessed ceiling mount assembly, sold separately).
- Pole The UAP FlexHD is attached to a pole (indoor or outdoor).
Note: When installing Ethernet cabling on a pole or up the outer surface of a wall, use RJ45 connectors without strain-relief boots on them. This will prevent unnecessary tension on the cable ends. |
Cable without a strain-relief boot | Cable with a strain-relief boot |
Proceed to the appropriate section for your installation.
Desktop
UAP-AC-EDU Quick Start Guide
Wall
Ceiling (Optional Accessory)
Cached
Use the optional Ceiling Mount, Mount Cover, and Back Plate Assembly to install the UAP FlexHD on a drop tile ceiling or horizontal surface where the interior side of the Ceiling Mount is accessible. |
Pole
Note: If you are mounting the UAP-FlexHD outdoors, it must be installed in the upright position to prevent water from getting into the base of the device. |
OR
UAP-FlexHD | |
Dimensions | Ø 48.50 x 159.49 mm (1.90 x 6.28') |
|---|---|
Weight | 315 g (0.69 lb) |
Networking Interface | (1) 10/100/1000 Ethernet Port |
Button | Reset |
LED | System |
Power Method | 802.3af PoE |
Power Supply | 802.3af PoE |
Max. Power Consumption | 10.5W |
Supported Voltage Range | 44 - 57VDC |
Operating Frequency | 2.4 GHz 5 GHz |
Max. TX Power | |
| 2.4 GHz | 23 dBm |
| 5 GHz | 26 dBm |
Throughput | |
| 2.4 GHz | 300 Mbps |
| 5 GHz | 1733 Mbps |
Antenna Gain | |
| 2.4 GHz | 1.6 dBi |
| 5 GHz | 4 dBi |
Wi-Fi Standards | 802.11 a/b/g/n/ac/ac-wave2 |
Wireless Security | WEP, WPA-PSK, |
Mounting | Desktop/Wall/Ceiling/Pole |
Operating Temperature | -30 to 70° C (-22 to 158° F) |
Operating Humidity | 5 to 95% Noncondensing |
Certifications | CE, FCC, IC |